Categories

Arai TX4 Move Red View full size

Arai TX4 Move Red

Arai TX4 Move Red 
Sizes:  XS - 2XL 
Mail: sales@trac-mac.com to confirm availability 

The Tour-X4 has a complete new outer shell. Redesigned to be tougher, stronger and stiffer than ever. As the Tour-X4 may be used under extreme conditions, the ventilation system has been redeveloped for maximum efficiency.

More details

110-905-

R 10.800,00

Reduced price!

-10%

R 12.000,00

Add to cart

By buying this product you can collect up to 108 loyalty points. Your cart will total 108 points that can be converted into a voucher of R 108,00.


The Tour-X 4 must be one of the most versatile helmets ever: adventure, grand touring or off road, and without the peak looks pretty good on a naked bike too! No matter the riding conditions, the Tour-X 4 is ready for it. Can be used without visor with goggles, without peak but with visor, any way that suits you.
Aluminum SilverAluminum SilverAluminum Silver


  • Tour-X4: Ventilation:
Easy to clean diffusers create a strong venture vacuum at the rear. Dual intake for increased airflow and lower noise level. Under-peak air intake collects and directs cool air into the helmet. Closable chin vent controls the airflow to the chin area. Inner chin vent shutter prevents debris coming into the helmet industy riding conditions. Brow ventilation, lower side vents and neck roll exhaust. Outer shell


  • Outer Shell Construction: Complex Fibre Laminate
Complex Fibre Laminate (CFL) employs special fibre layers bonded by unique resins formulated by Arai, producing an extremely high fibre to low resin ratio. This carefully managed construction delivers strength, structural integrity and impact flexibility which allows the rounded outer shell to do its main job – deflect, absorb and disperse impact energy over the widest possible area.


  • Front Ventilation: Dual intake
Designed for increased airflow and lower noise level, guiding fresh, cool air into the interior.


  • Front Ventilation: Standard brow vents
Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell and impact absorbing liner. For specific models the ventilation is extended to the temple area.


  • Front ventilation: Inner chin vent shutter
Open and close the chin bar vents from the inside to prevent debris coming into the helmet in dusty riding conditions.


  • Rear Ventilation: Neck exhaust vent
To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet.


  • Rear Ventilation: Removable diffuser
Creates a tremendous amount of venturi vacuum at the rear. Can be easily removed (for cleaning) or replacement.


  • Rear Ventilation: Side exhausts
Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise and prevent buffeting at speed. Inside, a small foam dam helps to absorb and diminish excessive noise, without reducing ventilation performance.


  • Aerodynamics: Pull Down Chin Spoiler
Helps minimize wind noise and also aids with the extraction of hot air from the face area. Provides additional deflection of road debris away from neck. Depending on the model the Chin Spoiler is retractable.


  • Visor: Pinlock insert lens
Effectively prevents misting and fogging of the visor, even under extreme wet and damp conditions. May be cleaned and changed easily.
 
 
  • Interior: Dry-Cool® Liner
Arai´s Dry-Cool® material transfers heat and moisture away from the rider quickly and efficiently.


  • Interior: Replaceable Cheek pads/Ear cups
Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water and mild soap. Rinse well after cleaning and never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider.
 
  • Interior: Replaceable Interior
Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water and mild soap. Rinse well after cleaning and never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider.

  • Interior: Replaceable Chinstrap covers
Depending on the model, cheek pads, ear cups or the complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water and mild soap. Rinse well after cleaning and never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider.

 
 
  • Interior: Facial Contour System (FCS)
To offer an even better snug fit and enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses and rebounds, providing the necessary support without excessive pressure.


  • Interior: 5mm ’’Peel Away’’ Ear cups/Cheek pads
Giving even more ability to craft the perfect fit and comfort, the cheek pads now feature a 5 mm peel away layer for added room if needed.


  • Interior: 5mm ’’Peel Away’’ Temple pad
Arai´s peel-away temple crown pads give the option of 5 mm more interior width* if needed.


  • Comfort: Emergency Release System (ERS)
Allows easier access to an injured rider. By pulling the orange tabs integrated in the pads, the cheek pads slide out. Making helmet removal easier for trained medical personnel and rescuers. Minimising the risk of additional injury.


  • Approval: ECE 22-05
The most common helmet certification internationally, required by over 50 countries worldwide.


  • General: Innovative peak
The Arai peak scavenges and forces air into the forehead vent ports for cooling while at the same time using multiple relief-ports to reduce “lifting” at higher speeds.


  • General: Five times inspected
Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting and graphic completion, after assembly and two in-process inspections.


  • General: Washable interior
The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap and lukewarm water.


  • General: Handmade
It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps and to build one Arai helmet will take about 18 man-hours.


  • General: All-day comfort
All-day comfort with the Arai interior fit and shape together with the finest liner materials and the extensive ventilation system. And thanks to the perfect balance and weight distribution of the helmet, you hardly notice you are wearing an Arai.


  • General: Penetration tested
All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet.


  • General: Double-D ring device
The flat and D-shaped rings fit smooth against the chin. No moving parts, no corrosion problems and just pulling the tab is enough to loosen the fastener.


  • General: Smooth shape, better protection
The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents and ducts are designed to break off during an impact.


  • General: Strong outer shell, soft inner shell
Arai uses a very strong outer shell to spread impact forces and a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component.


  • General: Organic shape
The organic shape of an Arai outer shell offers a more natural appearance, seals better and conforms more to the head’s natural shape for improved comfort, fit and to help minimize wind turbulence.


  • General: 5-year limited warranty
All Arai helmets are warranted against defects in materials and workmanship, and are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture.


  • General: Different outer shells
Unlike many other manufacturers Arai provides one size outer shell for each two-helmet sizes for most models. Together with different shaped outer shells for different models it is almost impossible not to find the fit you are looking for.


  • General: Arai In-house test
This Arai helmet is designed to meet the stringent Arai In-house criteria, in addition to the mandatory ECE 22-05 standard.



Manufacturers